Samsung WW25B6900A
✓ VERIFIEDFront-load washer2022
Typical Samsung WW25B6900A repair jobs and what they cost.
Repair
What’s involved
DIY
Parts
Labor
DIY
Moderate DIY
What’s involved
Replace drain pump.
Usually 1–3 days without it
Parts
Drain Pump
$58–$140
Labor
$150–$325
Drain Pump
Replace drain pump. Usually 1–3 days without it
Moderate DIY
Drain Pump
$58–$140
$150–$325
DIY
Advanced DIY
What’s involved
Door alignment and the interlock circuit are checked, then the failed lock/switch assembly is replaced.
Parts
Door Lock / Switch Assembly
$56–$109
Labor
$150–$325
Door Lock / Switch Assembly
Door alignment and the interlock circuit are checked, then the failed lock/switch assembly is replaced.
Advanced DIY
Door Lock / Switch Assembly
$56–$109
$150–$325
DIY
Advanced DIY
What’s involved
Replace door boot/gasket.
Usually 1–5 days without it
Parts
Door Seal / Boot Gasket
$104–$159
Labor
$150–$325
Door Seal
Replace door boot/gasket. Usually 1–5 days without it
Advanced DIY
Door Seal / Boot Gasket
$104–$159
$150–$325
DIY
Advanced DIY
What’s involved
Leveling and load conditions are ruled out, then worn shocks or suspension components are replaced as a matched set.
Parts
Shock absorber / strut / suspension-spring service part or kit
$40–$125
usually replaced as a set
Labor
$150–$325
Shock Absorbers / Suspension Springs
Leveling and load conditions are ruled out, then worn shocks or suspension components are replaced as a matched set.
Advanced DIY
Shock absorber / strut / suspension-spring service part or kit
$40–$125
usually replaced as a set
$150–$325
DIY
Technician job
What’s involved
Replace rear bearing and/or spider; often requires tub split or tub assembly.
Usually 3–7 days without it
Parts
Tub bearing
$72–$126
Spider arm / flange shaft assembly
$247–$280
Labor
$250–$425
Tub Bearing / Spider Arm
Replace rear bearing and/or spider; often requires tub split or tub assembly. Usually 3–7 days without it
Technician job
Tub bearing
$72–$126
Spider arm / flange shaft assembly
$247–$280
$250–$425
DIY
Advanced DIY
What’s involved
Supply screens and pressure are checked before the restricted or electrically failed valve assembly is replaced.
Parts
Water Inlet Valve
$61–$112
Labor
$125–$250
Water Inlet Valve
Supply screens and pressure are checked before the restricted or electrically failed valve assembly is replaced.
Advanced DIY
Water Inlet Valve
$61–$112
$125–$250
DIY
Advanced DIY
What’s involved
Power, lock, pump, motor, and sensor circuits are checked before replacing the failed control architecture.
Parts
Main control board
$225–$295
User interface board / console
$238–$364
Labor
$150–$325
Main Control Board / UI Board
Power, lock, pump, motor, and sensor circuits are checked before replacing the failed control architecture.
Advanced DIY
Main control board
$225–$295
User interface board / console
$238–$364
$150–$325
DIY
Easy DIY
What’s involved
The rear panel is removed and the broken, stretched, or thrown belt is replaced after pulley alignment is checked.
Parts
Drive Belt
$24–$49
Labor
$150–$325
Drive Belt
The rear panel is removed and the broken, stretched, or thrown belt is replaced after pulley alignment is checked.
Easy DIY
Drive Belt
$24–$49
$150–$325
DIY
Easy DIY
What’s involved
The washer is professionally cleaned and, when contamination is embedded or the boot is damaged, the door boot is replaced.
Parts
Door boot / bellow (torn, damaged, or non-remediable contamination only)
$100–$180
Labor
$150–$325
Door Boot Contamination (Mold)
The washer is professionally cleaned and, when contamination is embedded or the boot is damaged, the door boot is replaced.
Easy DIY
Door boot / bellow (torn, damaged, or non-remediable contamination only)
$100–$180
$150–$325
DIY
Technician job
What’s involved
The technician tests the motor windings, hall/tach sensor, harness, and control output, then replaces the failed motor-side component.
Parts
Drive motor
$249–$285
Stator
$192–$233
Rotor
$181–$203
Labor
$150–$325
Drive Motor / Stator / Rotor
The technician tests the motor windings, hall/tach sensor, harness, and control output, then replaces the failed motor-side component.
Technician job
Drive motor
$249–$285
Stator
$192–$233
Rotor
$181–$203
$150–$325
Easy DIY: basic tools, under an hour. Moderate: some disassembly. Advanced: experience with the machine's internals. Technician: sealed-system, electrical or tub-split work.
Parts prices don’t move much across the country; labor does. If a technician supplies the part, expect 40–50% on top of the part price.
ApplianceEdge assessments — lifespans, repair values, and reliability notes — are our editorial opinions, built from documented third-party sources: owner reports, industry pricing data, manufacturer literature, and official records. They describe patterns across a product family, not any individual machine; your experience may differ. Recall information links directly to official CPSC notices. We accept no payment from manufacturers, and no brand influences what we publish.